User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Sub Fluke 83,85,87 Freq & Duty Cycle (1 year) CAL VER
DATE:                  26-Sep-97
AUTHOR:                User Contributed
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       11
NUMBER OF LINES:       73
CONFIGURATION:         HP 3325B
STANDARD:              Stanford Research FS700
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-   R     N K            P J                          F        W
  1.002  ASK+                                          X
  1.003  STD          Stanford Research FS700
  1.004  HEAD         {* FREQUENCY TEST *}
  1.005  JMP          2.001
  1.006  EVAL
  2.001  DISP         Select the 400mV Range on the UUT.
  2.001  DISP         Press the Hz button to select the Frequency Counter.
  2.002  DISP         Connect the HP 3325A SIGNAL output to the
  2.002  DISP         UUT V Ohm Diode input using a 50 Ohm feedthrough
  2.002  DISP         termination.
  2.003  HEAD         FREQUENCY TESTS: {19.999kHz Range}
  2.004  JMP          3.001
  2.005  EVAL
  3.001  M3325                                     0Voff
  3.002  3325         19.000kH       0.005% 0.001U 150mV          SI       L
#!          Test Tol 1.95, Sys Tol 0.095, TUR 20.5263 (>= 4.00).
  4.001  HEAD         FREQUENCY TESTS: {199.99kHz Range}
  4.002  JMP          5.001
  4.003  EVAL
  5.001  3325         190.00kH       0.005% 0.001U 300mV          SI       L
#!          Test Tol 10.5, Sys Tol 0.95, TUR 11.0526 (>= 4.00).
  6.001  HEAD         {* FREQUENCY SENSITIVITY AND TRIGGER LEVEL TESTS *}
  6.002  JMP          7.001
  6.003  EVAL
  7.001  DISP         Press the Hz button to select Duty Cycle mode.
  7.002  JMP          8.001
  7.003  EVAL
  8.001  3325         100H                         425mV          SQ    S  L
  8.002  ACC          50.0pct        0.2%
  8.003  MEMI         Use keyboard to enter actual UUT reading in Percent:
  8.004  MEME
  8.005  MEMC         pct            4U
#!          Test Tol 4, Sys Tol 0.1, TUR 40.0000 (>= 4.00).
  9.001  DISP         Press the RANGE button to select the 4V range.
  9.002  3325         100H                         848mV          SQ    S  L
  9.003  ACC          50.0pct        0.2%
  9.004  MEMI         Use keyboard to enter actual UUT reading in Percent:
  9.005  MEME
  9.006  MEMC         pct            16U
#!          Test Tol 16, Sys Tol 0.1, TUR 160.000 (>= 4.00).
 10.001  DISP         Rotate the UUT function switch to VDC.
 10.001  DISP         Press the Range button to select the 4V range.
 10.001  DISP         Press the Hz button twice to select Duty Cycle mode.
 10.002  M3325                                     1.6Voff
 10.003  3325         100H                         3.4V           SQ    S  L
 10.004  ACC          50.0pct        0.2%
 10.005  MEMI         Use keyboard to enter actual UUT reading in Percent:
 10.006  MEME
 10.007  MEMC         pct            14U
#!          Test Tol 14, Sys Tol 0.1, TUR 140.000 (>= 4.00).
 11.001  DISP         Rotate the UUT function switch to OFF.
 11.002  DISP         Remove all connections.
 11.003  HEAD
 11.004  END
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  0
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.